Topic: Chris' HMS TIGER (C20) - 1:72 SCALE (Read 394173 times)

Dreadnought · « **Reply #1825 on:** November 18, 2022, 08:35:07 am »

Looks really good!

frogman3 · « **Reply #1826 on:** November 18, 2022, 10:21:43 am »

Quote from: Dreadnought on November 18, 2022, 08:35:07 am

Looks really good!

CHEERS Dreadnought

an more to fit on yet
chrisb

Sealord · « **Reply #1827 on:** November 22, 2022, 11:58:55 am »

Hi mate, Tiger looking brilliant.
Cant wait to come over and see it.

frogman3 · « **Reply #1828 on:** November 22, 2022, 12:07:05 pm »

Quote from: Sealord on November 22, 2022, 11:58:55 am

Hi mate, Tiger looking brilliant.
Cant wait to come over and see it.

HI BOYO well get better first an how you gettin over here if no car or will richard bring you an yes tiger is lookin great
ATB
CHRISB

frogman3 · « **Reply #1829 on:** December 06, 2022, 05:46:51 am »

HI ALL well ive i have been gettin on with it an ive been building them ships launches but not all of them as ive had to fit them on accros the beam of tiger due to H/J an they have been little blighters to build as has i got the shakes that dint help but still two more small rowin boats to fit on the main S/S an a small cabin cruiser but some pics first an here is the small cabin crusier still in build will show the finish pic later[/size]chrisb
https://ibb.co/C9zND3L[/size]

frogman3 · « **Reply #1830 on:** December 06, 2022, 05:50:06 am »

AN HERE i have started to build the big ships launch a cabin cruiser about 6 inches long
https://ibb.co/M9tZ3MH

frogman3 · « **Reply #1831 on:** December 06, 2022, 05:51:59 am »

an slowly gettin built
https://ibb.co/3TrpZys

frogman3 · « **Reply #1832 on:** December 06, 2022, 05:57:44 am »

an built an in its cradle on the deck an i have had to fit it accross the deck in stead of lenght wise due to H/J an ive also built an fitted the ships whale boats fitted in their deverts but cant fit all the boats that are shown on the plans as not enough room as these boats will lift out with the deck to fit in batt
https://ibb.co/QNr4QWp

frogman3 · « **Reply #1833 on:** December 06, 2022, 05:58:42 am »

side veiw of it
https://ibb.co/PTxDXfr

frogman3 · « **Reply #1834 on:** December 06, 2022, 05:59:32 am »

https://ibb.co/bFV1RJF

frogman3 · « **Reply #1835 on:** December 06, 2022, 06:02:42 am »

overall veiw now today ive got too fit on the motor launch an small boats on the front section
https://ibb.co/1LjKP9V

CHRISB

Rob47 · « **Reply #1836 on:** December 06, 2022, 07:44:41 pm »

Chris you not going to do the cut out where the David’s go?
Bob

frogman3 · « **Reply #1837 on:** December 06, 2022, 10:26:58 pm »

Quote from: Rob47 on December 06, 2022, 07:44:41 pm

Chris you not going to do the cut out where the David’s go?
Bob

HI Bob oh you mean boat devits fit on the deck an no i can do the cut out as i will cut through
the main hull strengher bar that goes whole ships length an if i do that cutout then the hull will fail an i dont want that

chrisb

Rob47 · « **Reply #1838 on:** December 07, 2022, 12:24:14 pm »

not sure i understand Chris it looks as if they are on the joint and the thickness of your joint bulkheads would not be impaired, or is there a huge bar each side?
Bob

frogman3 · « **Reply #1839 on:** December 07, 2022, 04:55:58 pm »

Quote from: Rob47 on December 07, 2022, 12:24:14 pm

not sure i understand Chris it looks as if they are on the joint and the thickness of your joint bulkheads would not be impaired, or is there a huge bar each side?
Bob

HI Bob where the cutout is on the plans an the build is about 3inches back from the hull jiont an its a half an inch thick qauqron to give the hull its strenght an if i cut through it to fit the cutout then that strenghening qaudront will be weak an the hull may then brake in two
hope you understand what i mean
chrisb

Rob47 · « **Reply #1840 on:** December 07, 2022, 06:46:26 pm »

Chris
I do now, shame really but more so if it fell to bits.
Hope Jen is ok and not feeling cold to much

Bob

frogman3 · « **Reply #1841 on:** December 07, 2022, 10:10:39 pm »

Quote from: Rob47 on December 07, 2022, 06:46:26 pm

Chris
I do now, shame really but more so if it fell to bits.
Hope Jen is ok and not feeling cold to much

Bob

YES Bob ive had to use a bit of modellers licence ON HER lol

BUT hopefully not many people will know its any differnt so im not worryied
chrisb

Sealord · « **Reply #1842 on:** December 08, 2022, 10:37:53 pm »

Hi mate ,ships boats are looking brilliant ..
whats the next stage ?

frogman3 · « **Reply #1843 on:** December 08, 2022, 10:48:22 pm »

Quote from: Sealord on December 08, 2022, 10:37:53 pm

Hi mate ,ships boats are looking brilliant ..
whats the next stage ?

got too build another boat im afraid an then build the fold down netting wherethe seacat missles will be mounted an then i hope to just jion her all up to finf out where the power section in for the aperture lights
chrisb

frogman3 · « **Reply #1844 on:** December 10, 2022, 10:05:05 am »

HI GUYS WELL a few more linkpicks
as yesterday i nearly dropped the SAR SEAKING so i thought id put both choppers on the flightdeck to see if they look ok an im pleased with the result
https://ibb.co/NsF5Qn4

frogman3 · « **Reply #1845 on:** December 10, 2022, 10:06:31 am »

AN HERE different angle shots ot them
https://ibb.co/PNMDNt1

frogman3 · « **Reply #1846 on:** December 10, 2022, 10:07:13 am »

https://ibb.co/QKN8QQX

frogman3 · « **Reply #1847 on:** December 10, 2022, 10:11:19 am »

an a SAR seaking in case the below happens
https://ibb.co/mtt4LCr
https://ibb.co/DV4Fjk6

frogman3 · « **Reply #1848 on:** December 10, 2022, 10:12:25 am »

https://ibb.co/vqgFVgC

frogman3 · « **Reply #1849 on:** December 10, 2022, 10:13:25 am »

https://ibb.co/FgbvCH6

AN now got to fit the other 2 seakings in the hangers being havin maintence done on them when i get round to it
chrisb

News:

Author Topic: Chris' HMS TIGER (C20) - 1:72 SCALE (Read 394173 times)